Gearench U116H-123S PETOL HYDRA-TORK Manual do Utilizador

Petol Hydra-Tork U116H-123S (Skid Mounted Base) Operating Manual Gearench P.O. Box 192 4450 South Highway 6 Clifton, Texas 766

8Periodic Inspection List for Petol Special Chain 1. PRIOR TO EACH USE, LEAF CHAIN AND TOOLS SHOULD BE INSPECTED FOR SERVICEABILITY AND LUB

9

10Safety Precautions 1. Always wear safety goggles to protect eyes. 2. Select the right tool for the job. 3. Keep tools in good condition.

11Installation Location The Petol Hydra-Tork Unit should be located in an area with adequate room to work the downhole tools. The unit may be locat

12Operation Controls The operating controls are shown on Figures 1 and 2 on page 16. The disconnect switch is used to disconnect electrical power t

13The hydraulic pressure gauge is used to indicate the current system pressure in psi. A conversion chart for equating the hydraulic pressure in ps

14

Loading To load the downhole tool in the unit, slide the vise left or right as needed. Adjust the vee-saddle to support the tool when set into the vi

16Breaking Out Load the tool and adjust the tong and vise as described above. Fully ratchet the tong. Turn the pressure control knob fully counter

Recommended Calibration Setpoints Pressure (psig) Torque (ft-lbs) Output (volts) 0 0 0.000600 10,150 1.0151200 20,300 2.0301800 30,450 3.0452400

iiTable of Contents Petol U116H-123S Hydra-Tork Description ... 1 Warranty ...

18Parts List The following drawings, diagrams, and parts lists describe all parts, which may be needed as replacement items. Where appropriate, sta

Final Assembly Parts List 19

20Final Assembly Parts List Item Qty. Part Number Description Notes 1 1 UHBASE-116H-02 Base assembly 2 1 UHCN-118-123 Console assembly Se

Console Assembly Parts List Item Qty. Part Number Description Make / Model Notes 1 1 UHCH-118-003 Hydraulic schematic 2 1 UHCN-P!-23 Control

Hydraulic Schematic 22

23Hydraulic Schematic Parts List Item Qty. Part Number Description Make / Model Notes 1 1 UHCH-P03 Pump Oilgear PVW-20-LSAY-NNNN-885B 2 1 UHC

Control Panel Parts List Item Qty. Part Number Description Make / Model Notes 1 1 UHCE-S1 Push button switch Allen-Bradley 800MB-CQA24GA 2 2

Main Electrical Panel Parts List Item Qty. Part Number Description Make / Model Notes 1A 1 UHCE-S7 Disconnect switch Allen-Bradley 194R-NJ030P3

263B 3 UHCE-H1 Heater, 230V Allen-Bradley W64 3B 3 UHCE-H2 Heater, 380/460V Allen-Bradley W56 4A 5 UHCE-W18 Cord connector Hubbell SHC1011 Or

Cylinder Carriage Parts List Item Qty. Part Number Description Make / Model Notes 1 1 UCC-A-1 Carriage arm 2 2 UCC-A-2 Caster McMaster-

1Petol U116H-123S Hydra-Tork Description The U116H-123S Petol Hydra-Tork unit was designed for making up and breaking out downhole tools. It is ra

2811 1 UHCY-116H-23 Main cylinder Vickers/Aeroquip TG10GRLA1AH18000 12 1 UHCE-W38 Galvanized nipple, 1/2” x close 13 1 UHCE-W37 Galvanized tee

Vee Saddle Assembly Parts List Item Qty. Part Number Description Make / Model Notes 1 1 UHVSB-116H Vee saddle base 2 1 UHVSH-116H Vee saddle h

Vise Assembly Parts List Item Qty. Part Number Description 1 1 TVB116H Base 2 1 TVJ116H Jaw 3 4 HI09D Diamond point insert 4 4 HP904 Insert key

Tong Assembly Parts List Item Qty. Part Number Description 1 1 UVTDH116H Handle 2 1 HP336 Handle pin 3 1 TVJ116H Jaw 4A 2 HI09D Diamond point

32Petol Special Chain Parts List Item Qty. Part Number Description 1 As req’d 161-45-02 Special chain only 2 As req’d 161-45-05 Special chai

Electrical Schematic 33

2Warranty What Is Covered Gearench tools are expressly warranted to you, the purchaser, to be free of defects in material and workmanship. How Lon

3Forum Selection Clause Any dispute arising out of the sale and/or use of the GEARENCH tool that is the subject of this limited warranty shall be pr

4Safe Practices and Procedures Responsibility "It is the responsibility of the employer to train the employee in the proper selection and usage

5Safety Goggles must always be worn by persons in any area where hand and powered tools are being used. Never apply excess leverage to a wrench or

6Responsibility of Distributors IT IS THE RESPONSIBILITY OF THE PURCHASERS OF GEARENCH PRODUCTS TO CONVEY THE INFORMATION IN THIS PUBLICATION AND AN

7Abrasives - Accelerated wearing and scoring of the articulating chain members (pins and plates) may occur, with a corresponding reduction in chain